TECHNOLOGY aligning surfaces of walls on beacons
As beacons best use the flashing profile, are easy to get at any hardware store.
Try and try to build lighthouses using cement-sand mortar or plaster is not necessary. Create enough flat and level strip of them will not work, and then place the joint beacons and basic solution is subject to delamination.
The installation of beacons start from the corners, and the distance between them is less than the length of the rules of 10 cm. In order to comply with the correct level of the installation, it is best to use screws that are screwed into a wall for most hat line location Beacon profile. On the upper screw hung a plumb line, and the rest be turned out of position when they are flush with the cap thread plummet. Do not forget that should be aligned to the same level as the screws on all lines of the profiles, as well as to bring the right angle between the plane of hats screws and the surface adjacent the walls of the room. Next set and secured themselves profile.
Along the edges of the lines and in several places in the mid-apply a small amount of solution. Beacon profile attach the line, so they went to their base on the cap screws and deepened little bumps solution. When the solution has dried, you can proceed directly to the plastering.
Application plaster
If the final layer of plaster will exceed 10-15 mm, the process of its application should be divided into two stages. The first call, distribute the solution on the wall and leveled so that it did not reach the level of the plane of the lighthouses around 5-10 mm. When the first layer of the solution dries, you can begin the final plastering.
The solution is applied with a small surplus and leveling the rule, which abuts ends on the flashing profile. Tools should be kept from the bottom upwards, slightly shaking it from side to side, in any case without taking it from the beacons. Best of all, if the smooth surface will already after the first pass.
The angles between the wall and the floor / ceiling of the output when the bulk of the solution has a bit sticking, but still moist. For this operation, use a special trowel to create internal corners.
When all the wall dried out properly, you can proceed to the removal of lighthouses. Strips left after them, seal the plaster solution, using ready-made sections of the level. Only in the case is expected to further laying ceramic tiles, can be left in the wall profile.
The final part of the work
As a result of this work already has a flat wall surface. However, no matter what materials to align the walls have been used in this way it would fit except for the tile, even in this embodiment, it should be primed. For all other cladding materials should be made and the grinding surface of the wall putty, finally leveling the wall surface to a smooth condition. Caulking is used at first start. A layer of putty applied in accordance with the manufacturer's mixture. For painting walls or thin wallpaper stickers also use putties, which is subsequently overwritten by a special net to perfectly smooth state.
As beacons best use the flashing profile, are easy to get at any hardware store.
Try and try to build lighthouses using cement-sand mortar or plaster is not necessary. Create enough flat and level strip of them will not work, and then place the joint beacons and basic solution is subject to delamination.
The installation of beacons start from the corners, and the distance between them is less than the length of the rules of 10 cm. In order to comply with the correct level of the installation, it is best to use screws that are screwed into a wall for most hat line location Beacon profile. On the upper screw hung a plumb line, and the rest be turned out of position when they are flush with the cap thread plummet. Do not forget that should be aligned to the same level as the screws on all lines of the profiles, as well as to bring the right angle between the plane of hats screws and the surface adjacent the walls of the room. Next set and secured themselves profile.
Along the edges of the lines and in several places in the mid-apply a small amount of solution. Beacon profile attach the line, so they went to their base on the cap screws and deepened little bumps solution. When the solution has dried, you can proceed directly to the plastering.
Application plaster
If the final layer of plaster will exceed 10-15 mm, the process of its application should be divided into two stages. The first call, distribute the solution on the wall and leveled so that it did not reach the level of the plane of the lighthouses around 5-10 mm. When the first layer of the solution dries, you can begin the final plastering.
The solution is applied with a small surplus and leveling the rule, which abuts ends on the flashing profile. Tools should be kept from the bottom upwards, slightly shaking it from side to side, in any case without taking it from the beacons. Best of all, if the smooth surface will already after the first pass.
The angles between the wall and the floor / ceiling of the output when the bulk of the solution has a bit sticking, but still moist. For this operation, use a special trowel to create internal corners.
When all the wall dried out properly, you can proceed to the removal of lighthouses. Strips left after them, seal the plaster solution, using ready-made sections of the level. Only in the case is expected to further laying ceramic tiles, can be left in the wall profile.
The final part of the work
As a result of this work already has a flat wall surface. However, no matter what materials to align the walls have been used in this way it would fit except for the tile, even in this embodiment, it should be primed. For all other cladding materials should be made and the grinding surface of the wall putty, finally leveling the wall surface to a smooth condition. Caulking is used at first start. A layer of putty applied in accordance with the manufacturer's mixture. For painting walls or thin wallpaper stickers also use putties, which is subsequently overwritten by a special net to perfectly smooth state.
Комментариев нет:
Отправить комментарий