How to door slopes
How would carefully not installing doors, without additional finishing door slopes can not do. Fortunately, you can make the door, and the slopes with their own hands, without resorting to the help of a specialist finisher.
You will need
- Profile (28 * 27);
- Profile (60 * 27);
- Drill with paddle;
- Gypsum board;
- Suspension;
- Foam or plaster;
- Plaster;
- water;
- An emphasis;
- Silicone;
- PVC plastic;
- Decorative corner;
- level;
- roulette;
- Malka;
- Cement.
Instructions
1. There are at least four ways to trim door slopes: PVC panels attach to the frame, installation of plasterboard on a metal or wooden frame, plastering slopes and pasting on drywall assembly foam or plaster. Choose which of these methods is suitable in your case and begin to implement it.
2. Make the door slopes of plasterboard on the frame. For this purpose the length of the slope on both sides attach profile (28 * 27) and transversely to them - the profile (60 * 27). Fix the profiles on the old door slopes, using the suspension. After mounting frame obsheyte his gispokartonom.
3. Follow the finish door slopes by attaching drywall to assembly foam or plaster. Measure the dimensions of the slope and it cut drywall.
4. Then attach the cut-out piece of plasterboard to the door slopes and aligning it with the levels, find out how this will be located design element.
5. Mix the plaster, adding a little putty (it is necessary to extend the time to plaster).
6. Apply the plaster solution from the edge of the slope continuous strip and glue it drywall. When used as a fastening element assembly foam, apply it to the surface of the slope, then attach drywall and make a special stop (the foam is able to grow in volume, so if you do not make a stop, it will slope of the curve).
7. Make the slopes of PVC panels to the frame: to expose this profile, fasten the plastic cover on it, which obkleyte decorative edge area (to glue the silicone).
8. Oshtukaturte slopes. First, determine the angle of inclination of slopes (slopes can be either deployed or in direct).
9. Then expose on the level of the wooden rail or aluminum rule, securing it to the wall with a nail. To make it easier to align the slopes, from a piece of wood to make a special Malki said.
10. After this, moisten with water and slope scribble solution on the slope, and then align it Malka. After about 15 minutes, remove the rail (usually). Slope ready.
note
Before you begin to work with the door slopes, paste over the door leaf packaging film and the box - masking tape.
Helpful advice
On sale there are ready-made slopes - "transoms". When choosing them, first of all, pay attention to colors: the color of slopes should be combined with the color of the door frame.
How would carefully not installing doors, without additional finishing door slopes can not do. Fortunately, you can make the door, and the slopes with their own hands, without resorting to the help of a specialist finisher.
You will need
- Profile (28 * 27);
- Profile (60 * 27);
- Drill with paddle;
- Gypsum board;
- Suspension;
- Foam or plaster;
- Plaster;
- water;
- An emphasis;
- Silicone;
- PVC plastic;
- Decorative corner;
- level;
- roulette;
- Malka;
- Cement.
Instructions
1. There are at least four ways to trim door slopes: PVC panels attach to the frame, installation of plasterboard on a metal or wooden frame, plastering slopes and pasting on drywall assembly foam or plaster. Choose which of these methods is suitable in your case and begin to implement it.
2. Make the door slopes of plasterboard on the frame. For this purpose the length of the slope on both sides attach profile (28 * 27) and transversely to them - the profile (60 * 27). Fix the profiles on the old door slopes, using the suspension. After mounting frame obsheyte his gispokartonom.
3. Follow the finish door slopes by attaching drywall to assembly foam or plaster. Measure the dimensions of the slope and it cut drywall.
4. Then attach the cut-out piece of plasterboard to the door slopes and aligning it with the levels, find out how this will be located design element.
5. Mix the plaster, adding a little putty (it is necessary to extend the time to plaster).
6. Apply the plaster solution from the edge of the slope continuous strip and glue it drywall. When used as a fastening element assembly foam, apply it to the surface of the slope, then attach drywall and make a special stop (the foam is able to grow in volume, so if you do not make a stop, it will slope of the curve).
7. Make the slopes of PVC panels to the frame: to expose this profile, fasten the plastic cover on it, which obkleyte decorative edge area (to glue the silicone).
8. Oshtukaturte slopes. First, determine the angle of inclination of slopes (slopes can be either deployed or in direct).
9. Then expose on the level of the wooden rail or aluminum rule, securing it to the wall with a nail. To make it easier to align the slopes, from a piece of wood to make a special Malki said.
10. After this, moisten with water and slope scribble solution on the slope, and then align it Malka. After about 15 minutes, remove the rail (usually). Slope ready.
note
Before you begin to work with the door slopes, paste over the door leaf packaging film and the box - masking tape.
Helpful advice
On sale there are ready-made slopes - "transoms". When choosing them, first of all, pay attention to colors: the color of slopes should be combined with the color of the door frame.
Комментариев нет:
Отправить комментарий